|The Ovation Fan Club|
|Random quote: "Believe me when I say that some of the most amazing music in history was made on equipment that's not as good as what you own right now." - Jol Dantzig|
| Glue Used for Fitting Neck to Body?|
|View previous thread :: View next thread|
|Member Communities -> Bottom Feeding Luthiery Guild||Message format|
I'm considering a neck reset on my 1990 Ovation Legend L717 (it's got the fretboard drop-off), so I was wondering what kind of glue the factory used to attach the fretboard onto the body?
From Youtube videos featuring Ovation neck resets it seems like some nasty stuff such as epoxy or some form of CA, definitely not hide glue. Can anybody confirm or deny this?
I'm concerned a neck reset would do more harm than good, especially if performed by a luthier not overly familiar with Ovation. Around where I live Ovation experts are pretty scarce; I have to lecture local luthiers each time not to file down the saddle and the like...
Edited by leonardmccoy 2017-09-10 4:42 PM
|Old Man Arthur|
Location: Keepin' It Weird in Portland, OR
|Uh... that neck joint in the photo is a Bolt-on. (or it should be) |
I am guessing that is not your guitar.
I have never glued a neck, so I will wait for wiser folks to answer.
Location: Lake Forest, CA
|Generally speaking, the factory used epoxy for most of the glue joints, including the fretboard extension. |
It can be removed with a heat gun. Once the epoxy reaches about 180 degrees it will soften and become rubbery. At this point it can be scraped off with little to no damage to the underlying surface.
Neck resets are only necessary when the action cannot be lowered be removing all the shims.
The fretboard drop-off is a by-product of the design of the Ovation guitar, itself. It's even discussed in one of the sales brochures.
If anything a neck reset will make the drop-off worse.
Is the L717 shown in the photo the guitar needing the neck reset?
Thanks for the valuable information.
The guitar needing the neck reset is not the guitar in the photo, but my lefty L717 Legend, also a bolt-on, which has the drop off starting at the 16th fret.
I have her in for a fretboard job currently. If anything like a neck reset were to be tried, my local luthier proposed, he would shim the area under the dropped-off fretboard piece so as make it straight again. In that sense it wouldn't be a regular neck reset which would entail correcting the neck angle to the body. In order to install the shimmed piece of wood he would still have to remove the neck from the body, though.
Do you still remember which brochure it was that marketed the fretboard drop-off as a feature? It seems the fretboard drop-off is a by-product of not strengthening the area underneath fretboard end enough. I would still not trade this A-braced Legend for any (potentially more structurally sound) X-braced guitar.
Since the action is still fine, and I still have two shims to go if I remember correctly which should be enough for the fretjob, it's probably not worth the risk then.
Edited by leonardmccoy 2017-09-11 1:20 PM
Location: Lake Forest, CA
My mistake. It wasn't the sales brochure, but the owner's manual that mentions the drop-off.
Thanks for your feedback and resourcefulness. The construction angle is super interesting to me. I'm surprised Ovation went the route of a perfectly flat top and even accounted for it in some way.
I have informed my luthier accordingly and leave the neck alone for now until I'm running out of shims.
I'm also still contemplating getting one of those new 2017 Glen Campbell signature guitars later this year.
Edited by leonardmccoy 2017-09-12 12:10 PM
|Jump to page : 1 |
Now viewing page 1 [25 messages per page]
|Search this forum|
Printer friendly version
E-mail a link to this thread
|This message board and website is not sponsored or affiliated with Ovation in any way.|
|(Delete all cookies set by this site)|