The Ovation Fan Club
The Ovation Fan Club
Forum Search | Statistics | User Listing Forums | Calendars | Albums | Language
Your are viewing as a Guest. ( logon | register )

Random quote: "One good thing about music, when it hits you, you feel no pain." - Bob Marley



Jump to page : 123
Now viewing page 1 [25 messages per page]
1974 1111 Balladeer Rebuild...

View previous thread :: View next thread
   Member Communities -> Bottom Feeding Luthiery GuildMessage format
 
DanSavage
Posted 2016-09-24 9:18 PM (#528978)
Subject: 1974 1111 Balladeer Rebuild...



Joined:
June 2012
Posts: 2303

Location: Lake Forest, CA

I found this sad 1974 1111-4 Balladeer on eBay a few months ago. It was pretty beat up.

The top was cracked in several spots,

One of the ears is mangled.

And, the neck needs stripping and refinishing.

I looked inside the guitar after I got it and found it had an early modified Ovation X-brace pattern, which is very similar to the original X-brace found on the 1960s Balladeers. The only really difference is the addition of the three scalloped tone bars between the lower X-braces.

Before stripping all the hardware off the guitar and pulling the top, I decided to string it up to hear what it sounded like. Even though I prefer 80/20s on the Ovation deep bowls all I had on hand was PBs. So, that's what I used. As I expected, the guitar has a rich sound that seems to be unaffected by the numerous cracks in the top. Because of this, I'm going to re-do this brace pattern in torrefied Sitka spruce. (naturally)

First order of business was to de-string it and strip all the hardware off it.

Next, pull the binding.

Now, separate the top from the bowl. Unfortunatley, the original silver foil label is long gone. I may have to forge one using Photoshop and my ALPS printer. :D

The neck angle is pretty good, so I don' think this will need a bowl bend. I'll check it more closely once clean all the old wood off the lining and get the remnants of the top out from between the fretboard extension and the neck block.

And, here's what the underside of the top looks like. It's pretty similar to the 1967 Balladeer I did for Jay with a couple of minor changes. First, instead of a 1/16" birch ply star joining the X-braces, it's got a single 1/16" strip that reinforces the notch in the bottom X-brace. And, as I noted previously, it's got the addtional three tone bars. I'm not sure how much these contribute to the sound, so if I were to hazard a guess I'd say these were added to help keep the top from bellying.

Top of the page Bottom of the page
seesquare
Posted 2016-09-24 9:40 PM (#528979 - in reply to #528978)
Subject: Re: 1974 1111 Balladeer Rebuild...


Joined:
November 2002
Posts: 3597

Location: Pacific Northwest Inland Empire
So, "We're Off to See The Wizard", again. Great news! Probably can't get much more "vanilla" than an early 1111, with a natural top. Let the transformation commence!
Top of the page Bottom of the page
Mike S.
Posted 2016-09-25 12:54 AM (#528982 - in reply to #528979)
Subject: Re: 1974 1111 Balladeer Rebuild...



Joined:
August 2002
Posts: 563

Location: Ottawa, Ontario, CANADA
Hi, Dan,
This " vanilla", model, the Ovation Standard Balladeer in Natural Finish,#1111-4, was the very first Ovation guitar I ever played. The one I played was made way back in 1969, though. Boy, oh, boy, let me tell you what, does seeing this one, even as beat up as it is, ever bring back some great memories. I'll be looking forward to seeing it again, fully restored, by you, of course! The bracing pattern is Ovations' own patent. They called this a,"Modified Fan", I do believe, but you can correct me on this, because you are a luthier, and I am not. Thanks so much for resurrecting this great guitar, because the sound on this guitar is just fantastic. This was BEFORE they invented their pickup! It will be a keeper when your work is completed.
Mike S.
Ottawa, ON. CANADA

Edited by Mike S. 2016-09-25 1:03 AM
Top of the page Bottom of the page
DanSavage
Posted 2016-09-25 4:36 PM (#528985 - in reply to #528979)
Subject: Re: 1974 1111 Balladeer Rebuild...



Joined:
June 2012
Posts: 2303

Location: Lake Forest, CA
seesquare - 2016-09-24 7:40 PM

So, "We're Off to See The Wizard", again. Great news! Probably can't get much more "vanilla" than an early 1111, with a natural top. Let the transformation commence!


Yep. In addition to this one, I'm going to be rebuilding a 1985 1717 at the same time. Since most of the work can be done in tandem, it almost as easy to do two guitars as it is to do one.

I'm going to wait to start on the 1717 until I get this one in the same condition and ready to accept the top.
Top of the page Bottom of the page
DanSavage
Posted 2016-09-25 4:43 PM (#528986 - in reply to #528982)
Subject: Re: 1974 1111 Balladeer Rebuild...



Joined:
June 2012
Posts: 2303

Location: Lake Forest, CA

Hi Mike,

At first I thought this guitar had the Ovation X seen below. But it's got a standard upper transverse brace which is perpendicular to the centerline rather than angled as shown below. Other than that, it's pretty similar.

Yeah, if it sounds anything close to how good Jay's Balladeer sounds, I'll be really happy with it. Intead of it using a walnut bridge, I'm going to be using an ebony bridge I got off a 1778 T. I'll also use a bone nut and bridge saddle.


Mike S. - 2016-09-24 10:54 PM

Hi, Dan,
This " vanilla", model, the Ovation Standard Balladeer in Natural Finish,#1111-4, was the very first Ovation guitar I ever played. The one I played was made way back in 1969, though. Boy, oh, boy, let me tell you what, does seeing this one, even as beat up as it is, ever bring back some great memories. I'll be looking forward to seeing it again, fully restored, by you, of course! The bracing pattern is Ovations' own patent. They called this a,"Modified Fan", I do believe, but you can correct me on this, because you are a luthier, and I am not. Thanks so much for resurrecting this great guitar, because the sound on this guitar is just fantastic. This was BEFORE they invented their pickup! It will be a keeper when your work is completed.
Mike S.
Ottawa, ON. CANADA

Top of the page Bottom of the page
Mike S.
Posted 2016-09-25 5:07 PM (#528987 - in reply to #528986)
Subject: Re: 1974 1111 Balladeer Rebuild...



Joined:
August 2002
Posts: 563

Location: Ottawa, Ontario, CANADA
Hi, Dan,
Thanks for the kind reply. and new information about your work on these guitars. Wow, two at once, eh? I'm Canada's worst handyman, and I have trouble just changing the strings on my guitars sometimes! I'm looking forward to seeing these two beauties restored to their full guitar glory real soon.
Best regards,
Mike S.
Ottawa, ON. CANADA
Top of the page Bottom of the page
DanSavage
Posted 2016-10-03 8:23 PM (#529095 - in reply to #528978)
Subject: RE: 1974 1111 Balladeer Rebuild...



Joined:
June 2012
Posts: 2303

Location: Lake Forest, CA

Hi Mike,

Yeah, once the guitars get to a certain point, it's just as easy to work on two at a time as it is to work on one. The 1717 is at the point where it's ready for the new top, so I've got to get the 1111 to the same point.

Prior obligations have kept me from working on these two guitars this week, but I was able to get back to this one today.

First job was to scrape the lining clean of the remnants of the old top and to clear out the area between the neck block and the fretboard extension.

Once this was done I was able to slip an old top into place and drop a bridge into place to check the neck alignment.

Looks good. No bowl bend will be necessary. (Yay!)



I got some new rosettes from the MS which use a light grey background instead of pearloid.

To keep the vintage feel of the guitar I used a heat gun to soften the epoxy holding the original rosette. For the most part, it came off pretty cleanly. I'll need to glue the pearloid and use to black paint to touch up the parts that stayed stuck to the top.  I'm not sure if I'll use these or the rosette I pulled off the top. It depends on how the original one looks when I get done with it. The pearloid is pretty yellowed and doesn't really show that much 'pearl' any more.

I used Ken's (arumako) technique of boiling hot water in a ziplock baggie to soften the epoxy holding the bridge down. I'm very impressed with how well it worked. The bridge came off the top without any damage at all. Even the original routing groove remained intact.



Some of the glue separated from the top and stayed stuck to the bridge, but the use of more boiling hot water softened the epoxy enough that I was able to use my Xacto chisel to remove it.

Next job is to remove the finish from the neck and head stock, then start repair the broken ear.



Edited by DanSavage 2016-10-03 8:25 PM
Top of the page Bottom of the page
Love O Fair
Posted 2016-10-03 10:22 PM (#529100 - in reply to #528978)
Subject: Re: 1974 1111 Balladeer Rebuild...



Joined:
February 2016
Posts: 1764

Location: When??
I may have said this before.. but in addition to the awesome stories you let us witness unfold on your guitar projects, I sometimes enjoy finding a secondary interest in the nifty tools and gadgets seen laying on the bench (okay, so I'm into details), and it all seems to fit the rhyme and reason, though I have to say that the bottle of crabgrass killer has definitely piqued my curiosity on this one.
Top of the page Bottom of the page
DanSavage
Posted 2016-10-04 11:34 AM (#529112 - in reply to #528978)
Subject: Re: 1974 1111 Balladeer Rebuild...



Joined:
June 2012
Posts: 2303

Location: Lake Forest, CA
Haha!

The crabgrass killer is on my desk/workbench because I was going to use it on the front and back lawn until I found out that what I thought was crabgrass was really kikuyugrass. Unfortunately, normal methods of weed control don't work on kikuyugrass.
Top of the page Bottom of the page
DanSavage
Posted 2016-10-05 8:57 PM (#529150 - in reply to #528978)
Subject: RE: 1974 1111 Balladeer Rebuild...



Joined:
June 2012
Posts: 2303

Location: Lake Forest, CA

I sanded the finish off the head stock and neck today.



Unfortunately, I got a little too over-exuberant and burned through the finish on the bowl. (oopsie!) This will be repaired later.

Next job is to get a small chunk of matching mahogany and repair the broken ear. But, before I start the ear-repair, I'll prepare the top wood and braces for both this guitar and the 1717. Then, while the top wood joint(s) are drying I'll repair the ear.

Top of the page Bottom of the page
DanSavage
Posted 2016-10-08 6:35 PM (#529206 - in reply to #528978)
Subject: RE: 1974 1111 Balladeer Rebuild...



Joined:
June 2012
Posts: 2303

Location: Lake Forest, CA

I got the top wood jointed this morning. I'll take this top with me to the sanders Monday morning and get both the 1717 and this one done at the same time.

Next job was to make the braces. Everything shown is in its approximate position.



Here the braces are shown next to the old top.

I was able to clean up the mangled ear and glue a mahogany block to it using OBG. But, when I shaped the block, I found that the color and grain of the patch piece didn't even come close to matching the head stock wood, even with staining. I'm really glad now I used OBG instead of epoxy or CYA as I was able to steam it off. I'll search around to see if I can find a piece that matches a little bit better. I'll also contact the MS to see if JB can grab a piece of scrap off the shop floor, drop it into an envelope and mail it to me.

Top of the page Bottom of the page
DanSavage
Posted 2016-10-11 3:12 PM (#529256 - in reply to #528978)
Subject: RE: 1974 1111 Balladeer Rebuild...



Joined:
June 2012
Posts: 2303

Location: Lake Forest, CA

I got the top cut out. Drilled the bridge locating pins (more on that below) and cut the sound hole.

This wood has some figuring that almost makes it look like bearclaw. It also has some nice silking. It should make for a pretty guitar.



Brace pattern is laid out on the underside. You'll notice that one of the bridge pin holes is oblong. That's because I measured one and assumed that both were the same distance from the front of the bridge. Wrong! This means I'll have to carefully align the bridge when I lay the masking tape down prior to finishing.



Braces ready to be glued down. Once I take the 1717 soundboard out of the gobar deck this afternoon, I'll glue down the braces with OBG.

Top of the page Bottom of the page
BanjoJ
Posted 2016-10-11 5:00 PM (#529259 - in reply to #528978)
Subject: RE: 1974 1111 Balladeer Rebuild...



Joined:
September 2012
Posts: 809

Location: Thredbo, NSW, Australia
Thanks Dan. I'm loving this and the 1717 story. Keep em coming!
Top of the page Bottom of the page
moody, p.i.
Posted 2016-10-11 11:34 PM (#529263 - in reply to #528978)
Subject: Re: 1974 1111 Balladeer Rebuild...


Joined:
March 2002
Posts: 15649

Location: SoCal
If you ever played one, you'd love them even more. My Savage 1113 is the one guitar that gets played every day.....
Top of the page Bottom of the page
DanSavage
Posted 2016-10-12 8:56 AM (#529267 - in reply to #528978)
Subject: RE: 1974 1111 Balladeer Rebuild...



Joined:
June 2012
Posts: 2303

Location: Lake Forest, CA

Thanks, guys.

Braces are glued. I'll pull this out of the gobar deck later this afternoon, then it's time to glue the top to the bowl of both this one and the 1717.

Top of the page Bottom of the page
DanSavage
Posted 2016-10-12 8:42 PM (#529275 - in reply to #528978)
Subject: RE: 1974 1111 Balladeer Rebuild...



Joined:
June 2012
Posts: 2303

Location: Lake Forest, CA

Faux foil label. I was able to print it using my Alps printer foil cartridge and it looked great under certain angles, but this looks better under all angles. It's not reflective like real foil, but this is better than no label at all.

Top being glued to bowl.



Edited by DanSavage 2016-10-12 8:43 PM
Top of the page Bottom of the page
DanSavage
Posted 2016-10-13 12:43 PM (#529287 - in reply to #528978)
Subject: RE: 1974 1111 Balladeer Rebuild...



Joined:
June 2012
Posts: 2303

Location: Lake Forest, CA

The glue joint between bowl and top was hard enough to pull the weights off.

Gluing fretboard extention to soundboard.

I'll sand down the excess top material from around the bowl tomorrow once the fret extension glue has had a chance to cure. Once that's done the top will be ready for routing for binding and purfling.



Edited by DanSavage 2016-10-13 12:44 PM
Top of the page Bottom of the page
DanSavage
Posted 2016-10-17 6:13 PM (#529353 - in reply to #528978)
Subject: RE: 1974 1111 Balladeer Rebuild...



Joined:
June 2012
Posts: 2303

Location: Lake Forest, CA

Binding and purfling channels are routed.



And, glued into place. I'll let the glue dry until tomorrow, then start scraping.

Top of the page Bottom of the page
arumako
Posted 2016-10-18 6:16 AM (#529364 - in reply to #528978)
Subject: Re: 1974 1111 Balladeer Rebuild...



Joined:
October 2012
Posts: 1018

Location: Yokohama, Japan
WOW! Coming along nicely...again! Shiny Bowl?
Top of the page Bottom of the page
DanSavage
Posted 2016-10-18 8:54 AM (#529368 - in reply to #528978)
Subject: Re: 1974 1111 Balladeer Rebuild...



Joined:
June 2012
Posts: 2303

Location: Lake Forest, CA
Thanks, Ken. Not a shiny bowl. I think they stopped making shiny bowls in the late 1960s.
Top of the page Bottom of the page
DanSavage
Posted 2016-10-18 6:53 PM (#529372 - in reply to #528978)
Subject: RE: 1974 1111 Balladeer Rebuild...



Joined:
June 2012
Posts: 2303

Location: Lake Forest, CA

Binding tape pulled up.

Binding and purfling scraped level. Top is ready for finishing. But, before I start that I need to turn my attention to the headstock repair. As with the other guitars, I'll finish the neck first, then do the body.

 

Top of the page Bottom of the page
DanSavage
Posted 2016-10-25 11:16 AM (#529490 - in reply to #528978)
Subject: RE: 1974 1111 Balladeer Rebuild...



Joined:
June 2012
Posts: 2303

Location: Lake Forest, CA

Time to turn my attention to the broken headstock. Here's what it looked like before I started.

After I sanded the finish off, I sanded the broken section flat to prepare it for gluing the patch piece.

I bought some mahogany planks locally, and made several attempts, but they didn't come close to matching the grain pattern of the head stock. Thankfully, I followed my first instinct and glued the patches on with OBG, so they were easy to steam off and try again.

So, I sent an email to JB at the MS and asked him if he could send some scraps. Here's what I got back. The darker pieces are from the sealer applied to ends of the raw stock that they used to laminate. The actual wood is the same color as the lighter wood on the other side of the laminations. (they're bookmatched)

But, when I oriented the grain to match that of the head stock, I had the same problem as the locally-sourced wood -- the grain pattern didn't match. The solution was to turn the piece 90 degrees and use the end-grain, instead. Here's a shot of final patch piece glued into place and sanded to shape. The existing head stock wood is quite a but darker than the patch piece.

When it's wet out, you can see the difference in color between the old wood and the new wood. The grain matches pretty good, but it's quite a bit lighter in color. So, the next job was to find a way to stain the patch to get it to match the coloration of the head stock wood when it's wetted out.

I used the scrap wood JB sent as test pieces so I could find out what worked best. I ended up using alternating coats of thinned Minwax red oak stain and shellac tinted with burnt sienna and raw umber dry artists pigment to build up the finish to get the best match without overshooting the tint and making it too dark.

Here's what the finished patch looks like when it's dry.

And, when it's wetted out with naptha to simulate how the clear coat will look. The direction of the grain is slightly off, but it's close enough that it will pass all but the closest inspection.

Now that this job is done, it's time to mask off the neck and start applying the clear coat.

 



Edited by DanSavage 2016-10-25 11:28 AM
Top of the page Bottom of the page
jay
Posted 2016-10-25 12:32 PM (#529491 - in reply to #529490)
Subject: RE: 1974 1111 Balladeer Rebuild...



Joined:
January 2009
Posts: 1249

Location: Texas

We need "Like" buttons!
Dan, just saying it again....Thank you for taking the time in documenting these rebuilds. The journey is always different and each post is tremendously interesting.  

Top of the page Bottom of the page
Old Man Arthur
Posted 2016-10-25 1:11 PM (#529493 - in reply to #528978)
Subject: Re: 1974 1111 Balladeer Rebuild...



Joined:
September 2006
Posts: 10777

Location: Keepin' It Weird in Portland, OR
Really, Really, impressive.
Top of the page Bottom of the page
BanjoJ
Posted 2016-10-25 3:29 PM (#529495 - in reply to #529491)
Subject: RE: 1974 1111 Balladeer Rebuild...



Joined:
September 2012
Posts: 809

Location: Thredbo, NSW, Australia
jay - 2016-10-26 5:32 AM

We need "Like" buttons!
Dan, just saying it again....Thank you for taking the time in documenting these rebuilds. The journey is always different and each post is tremendously interesting.  



+1

I'm loving this one. Very interesting.
Top of the page Bottom of the page
Jump to page : 1 2 3
Now viewing page 1 [25 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread

This message board and website is not sponsored or affiliated with Ovation® Guitars in any way.
Registered to: The Ovation Fanclub™ Copyright (c) 2001
free counters
(Delete all cookies set by this site)