|
|
Joined:
September 2006
Posts: 10777
Location: Keepin' It Weird in Portland, OR | We'll start with the Headstock... I did a cosmetic upgrade to my 2778LX:
Before...
After...
General consensus... Do you think that I need to hunt-down a Gold LX TRC?
Next Question... And this is more important than cosmetics, I think:
Can y'all see the "pits" in the rosewood fretboard?
  
Is this something that I should be concerned about, and try to remedy?
Or is it something that is no big deal, and if I hadn't noticed it until now... don't worry about it?
Any advice, opinions, or sage wisdom would be appreciated. :cool:
-add on-
This is a 2778LX-4.... quick pic
 |
|
| |
|
Joined:
September 2002
Posts: 806
Location: Seymour, Tennessee | Don't know bout the fretboard but I say yes for agold inlay TRC.
Those tuners & buttons look great. |
|
| |
|
Joined:
August 2002
Posts: 8307
Location: Tennessee | The first thing I'd do is use 0000 steel wool on the fretboard to clean off all that gunk, then oil it, then evaluate. How are the frets?
I like the buttons. I vote for a plain TRC sans writing.
The guitar looks like it's been well played which could be a good thing. Is it new to you? |
|
| |
|
Joined:
September 2006
Posts: 10777
Location: Keepin' It Weird in Portland, OR | Originally posted by stonebobbo:
Is it new to you? Yes... I got it just before Christmas.
It is supposedly New to everyone with paperwork, four shims and a tether on the preamp.
I cleaned it off with a damp rag to loosen the dust, then mineral oil and my thumbnail.
Those are not dents in the frets, but it is where the shiny wore off.
Or where the coating on the strings got on the frets, or something...
This was listed as New, but since they haven't made these for two years... I can't be that new. |
|
| |
|
Joined:
August 2002
Posts: 8307
Location: Tennessee | The 0000 steel wool will clean off those frets, too. I'm viewing this on a smaller device, but that guitar looks like it has a lots of miles on it for a new guitar. |
|
| |
|
Joined:
October 2005
Posts: 4081
Location: Utah | My 2 cents:
Custom TRC with OMA inlaid in brass. Or a plain TRC. You could flip over the one you have and sand the back side with some 800 or 1600 grit paper to smooth it out, then install it back side up. Or a gold TRC. The silver LX does clash.
I wouldn't worry about the pits. If it really bothers you, some 400 grit wet sandpaper to lightly knock down the sharper edges will reduce the appearance of roughness without changing the shape of the fretboard. Then fine sanding with progressively finer grit to smooth it out.
Steel wool leaves little bits of metal that I don't like, so I prefer to use very fine grit polishing paper or a dremel buffing wheel for frets. The dremel works well but leaves gunk that has to be cleaned off of the fretboard. |
|
| |
|
Joined:
February 2003
Posts: 86
Location: northern virginia | You may want to consider trying the Dunlop "02 fretboard deep conditioner"...this stuff has done wonders on the appearance and feel of the grain on my rosewood boards...I'd almost go as far as saying it appears to close up the pores and plump up the wood cells...but with no impact on the frets...I consider this stuff to be restorative in a sense. |
|
| |
|
Joined:
May 2008
Posts: 4996
Location: Phoenix AZ | I would recommend using steel wool rather than your thumbnail |
|
| |
|
Joined:
September 2006
Posts: 10777
Location: Keepin' It Weird in Portland, OR | Roundsound, that sounds good. I just ordered some Dunlop 02, I'll give that a try.
I will see about shining-up the frets next string change.
Bobbo sez; "but that guitar looks like it has a lots of miles on it for a new guitar"
No Pick Tracks, tho'... :cool: |
|
| |
|
Joined:
April 2008
Posts: 2985
Location: Sydney, Australia | The Wizz filled in the potholes on my 12 string
and the result was spectacular:
Yours doesn't look anywhere near this bad though. |
|
| |
|
Joined:
September 2006
Posts: 10777
Location: Keepin' It Weird in Portland, OR | Not quite that bad, Richard.
Apparently y'all cannot see what I am talking about.
Mine just has teeny little dents all over it...
Kinda evenly dispersed.
I did not notice them until I took the strings off.
There are no fingernail divots.
(I had a 1718 like that once) |
|
| |
|
Joined:
April 2008
Posts: 2985
Location: Sydney, Australia | Oh, I see them now. I wouldn't worry about them. Looks like that's the texture of the wood. If you sanded it down, you'd probably find more little holes popping up from underneath. |
|
| |
|
Joined:
December 2008
Posts: 1456
Location: Texas | Originally posted by TAFKAR:
Oh, I see them now. I wouldn't worry about them. Looks like that's the texture of the wood. If you sanded it down, you'd probably find more little holes popping up from underneath. I agree, I have several necks that have a similar appearance… I wouldn't do anything more than a light cleaning/oiling of the fretboard. (I like the Dunlop System .)
Those tunas look nice on there, put some strings on and play it! |
|
| |
|
Joined:
September 2006
Posts: 10777
Location: Keepin' It Weird in Portland, OR | Originally posted by standing:
Those tunas look nice on there, put some strings on and play it! I did that right after I took the pics. :D |
|
| |
|
Joined:
February 2005
Posts: 11840
Location: closely held secret | At least we know your priorities. |
|
| |
|
Joined:
September 2006
Posts: 10777
Location: Keepin' It Weird in Portland, OR | I take photos of all my projects.
All my incoming and outgoing packages, too.
That way I won't say, "Damn, I shoulda taken photos." |
|
| |
|
Joined:
September 2009
Posts: 144
Location: SW Washington | Steel wool leaves little bits of metal that I don't like, so I prefer to use very fine grit polishing paper or a dremel buffing wheel for frets. anytime I use steel wool on my fingerboards, I wrap the steel wool around a strong magnet and the magnet collects 99% of the filings. Works pretty good. |
|
| |
Coupla Questions about Headstocks and Fretboards...
