|
|
Joined:
August 2002
Posts: 8307
Location: Tennessee | Is there a special tool or trick for adjusting the truss rod? Seems none of the wrenches I have can turn the nut far enough to be able to re-insert the wrench to turn farther. The handles are too long and get hung up on the cavity so that I can't get more than about an eighth of a turn. Anyone else run into this? |
|
| |
|
Joined:
January 2006
Posts: 5881
Location: Colorado Rocky Mountains | No help here. Haven't had to adjust the neck on any of mine. |
|
| |
|
Joined:
November 2004
Posts: 367
Location: Eaton, Indiana | Had to do surgery on mine.
scott |
|
| |
|
Joined:
May 2008
Posts: 1565
Location: Indiana | I use a miniature socket wrench with an allen bit. |
|
| |
|
Joined:
February 2002
Posts: 5750
Location: Scotland | Try a ball-end Allen key. |
|
| |
|
Joined:
August 2002
Posts: 8307
Location: Tennessee | Thanks. I tried earlier to find a miniature socket solution but my local hardware didn't have the right combination. Didn't think about a ball end. Either way, a trip to another hardware store in on. |
|
| |
|
Joined:
February 2002
Posts: 5750
Location: Scotland | The Cruz guitar multi-tool might work |
|
| |
|
Joined:
January 2006
Posts: 5881
Location: Colorado Rocky Mountains | Bob, coincidently, I had to make a slight adjustment on my EA58 (12 string) neck this weekend. I went through my gig bag tools and found an allen wrench with both ends bent 90 degrees, one of which was offset by 45 degrees from the other. The tool works just like an offset open end wrench. By alternating ends, the allen wrench works in the limited neck cavity space. This may very well be the tool that comes from the factory with the EA58/63/68 models. |
|
| |
|
Joined:
January 2002
Posts: 14127
Location: 6 String Ranch | i think it might be. |
|
| |
|
Joined:
December 2001
Posts: 10583
Location: NJ | yes |
|
| |
|
Joined:
August 2002
Posts: 8307
Location: Tennessee | Thanks. I did not get the factory tool with my guitar. I'll contact the factory and see if they still have any of them. |
|
| |
|
Joined:
February 2007
Posts: 302
Location: Nashville, TN | Yes...3 of mine came with a neck adjustment tool...odd "s" snakey looking thing |
|
| |
|
Joined:
August 2002
Posts: 8307
Location: Tennessee | Well, if any of you out there have a line on an extra snakey looking hex key for a Viper, let me know. ;) Thanks. |
|
| |
|
Joined:
December 2004
Posts: 1673
Location: SoCal | No luck at the Factory, bobbo?
Going to be in our neighborhood (or close) any time soon... or I'm driving up to Rivera in Burbank some time next week. |
|
| |
|
Joined:
August 2002
Posts: 8307
Location: Tennessee | Still waiting to hear from back from the factory ... they didn't find one right away but were still checking all the little cubbys and crevices. So I'm onto Plan C now. No worries. Not planning on being in SoCal anytime soon, Noah. But I do like the stuff Paul Rivera does ... you visiting with them? |
|
| |
|
Joined:
December 2004
Posts: 1673
Location: SoCal | 
Yep, the amp is going back home for some upgrades that I will never get to otherwise. It will be mon, wed, or fri. I've never been there and as much as I'd like to, do they let mere mortals visit? I just pictured going up to a counter and walking away with a drop-off ticket. You can also email your address and I can priority mail one to you. |
|
| |
|
Joined:
August 2002
Posts: 8307
Location: Tennessee | Nice rig, Bruce. Thanks for the offer, too.
Has anyone around here lately said just how great Ovation customer service is? They found a wrench and got it to me. Awesome. |
|
| |
Question for EA-68 Viper owners
