The Ovation Fan Club
The Ovation Fan Club
Forum Search | Statistics | User Listing Forums | Calendars | Albums | Language
Your are viewing as a Guest. ( logon | register )

Random quote: "Jazz... isn't that just a series of mistakes disguised as musical composition?” - David St. Hubbins of Spinal Tap



Jump to page : 1
Now viewing page 1 [25 messages per page]
Broken Brace

View previous thread :: View next thread
   Members Forums -> General PostingMessage format
 
TAFKAR
Posted 2014-10-17 7:41 PM (#496047)
Subject: Broken Brace



Joined:
April 2008
Posts: 2985

Location: Sydney, Australia

While tightening the truss rod on my Adamas II 12 string, I have split one of the braces (the truss rod was VERY tight, even though I'd taken all the strings off).

 Broken brace 

You can see the broken brace - the one immediately to the right of the truss rod.

 

Here's the broken section:

The broken bit

 

Any words from the wise before I attempt to glue this back together?

Top of the page Bottom of the page
arumako
Posted 2014-10-17 8:54 PM (#496048 - in reply to #496047)
Subject: Re: Broken Brace



Joined:
October 2012
Posts: 1034

Location: Yokohama, Japan		Ouch! No word from the wise here, but just wanted to wish you and your Adamas a quick and healthy recovery!
Top of the page Bottom of the page
FlySig
Posted 2014-10-17 9:21 PM (#496049 - in reply to #496047)
Subject: Re: Broken Brace



Joined:
October 2005
Posts: 4042

Location: Utah		I am not an expert but I'll offer an opinion.

I'd use either a top quality carpenter's glue or hide glue. The liquid hide glue is tempting, and has similar strength to the carpenter's glue, slightly less strength than hot hide glue. Any of those should be stronger than the wood itself if applied properly. So I would go with carpenter's glue because it will clean up with water.

The critical workmanship issue will be to get the wood pieces to fit back together very tightly. And then get the excess glue cleaned up before it hardens. A minimal amount of glue to ensure the joint is solid but there is no excess globs like Dan found on the '67 Balladeer project. http://www.ovationfanclub.com/megabbs/forums/thread-view.asp?tid=40...

If you can get a long armed clamp or two in there through the epaulet holes that would be ideal. If not, some kind of weighting to hold the loose piece down firmly while the glue sets.

I would not resort to screws or doublers, as the added weight would be harmful to tone.

When a brace popped loose on my Patriot it glued down easily with carpenter's glue. No problem with joint strength.
Top of the page Bottom of the page
BanjoJ
Posted 2014-10-18 12:58 AM (#496052 - in reply to #496047)
Subject: RE: Broken Brace



Joined:
September 2012
Posts: 811

Location: Thredbo, NSW, Australia		Ouch!

A lot of people here on OFC recommend Titebond, which isn't all that common in Australia. However, Masters hardware carry it.

Here's a couple of photos of the clamp that I made from a turnbuckle when I repaired the broken braces on my Folklore.

Good luck with the repair.







(Turnbuckle.JPG)



(1614-Internals-33.jpg)



Attachments
----------------
Attachments Turnbuckle.JPG (73KB - 0 downloads)
Attachments 1614-Internals-33.jpg (23KB - 0 downloads)
Top of the page Bottom of the page
Jump to page : 1
Now viewing page 1 [25 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread

This message board and website is not sponsored or affiliated with Ovation® Guitars in any way.
Registered to: The Ovation Fanclub™ Copyright (c) 2001
free counters
(Delete all cookies set by this site)