|
|
Joined:
August 2002
Posts: 8307
Location: Tennessee | A piece of the wood in the epaulet on my 2000 collectors appears to be peeling up and I'm wondering if it is safe for me to attempt to reglue. It it where the walnut meets the maple, in the very, very thin part between the largest hole and the mid-size hole on the upper bout. Any suggestions on type of glue I should use, anything to watch out for, etc. It doesn't seem significant enough to spend the time and money to send back to the factory. Also, is this a common occurance? Thanks in advance. |
|
| |
|
Joined:
January 2002
Posts: 14127
Location: 6 String Ranch | A squirt of crazy glue. Make sure you don't get your fingers stuck. |
|
| |
|
Joined:
December 2001
Posts: 10582
Location: NJ | i think they use titebond at the factory. I have seen a few epaulets cut loose but not often. |
|
| |
|
Joined:
June 2002
Posts: 123
Location: Pensacola,FL | The factory or a luthier would use Titebond
yellow (carpenter's glue) and inject it under the
leaf (so no mess, no seen glue). ;) |
|
| |
|
Joined:
October 2002
Posts: 61
| Titebond will not hold.You should use super/crazy glue as was suggested .The factory uses loctite.
The lifted eppie is more common than we like to admit. |
|
| |
|
Joined:
August 2002
Posts: 8307
Location: Tennessee | Hehe. Thanks for the advice. Actually have a tube of loctite in the toolbox for using on the set screw of the points for the 009 distributor on the old Veedubs. Never underestimate the usefulness of all things volkswagen ... reminds me of the time I talked the date out of her pantyhose to rectify a thrown belt ... got her home on time but still suffered the scorn of her father. |
|
| |
|
Joined:
December 2001
Posts: 10582
Location: NJ | loctite was what I was thinking when I typed titebond...sorry carry on.. |
|
| |
|
Joined:
May 2002
Posts: 3005
Location: Las Cruces, NM | Stonebobo
I have two daughters and I never would have believed that story, especially from someone in a VW. All I can say is you would have been glad you had a rear engine car as the shotgun blasts followed your rapid escape. The only thing that would save you would be there was no radiator to get penetrated.
Bailey |
|
| |
|
Joined:
October 2002
Posts: 4
| I thought penetrattion was the whole point of this story! ;) |
|
| |
|
Joined:
January 2002
Posts: 14127
Location: 6 String Ranch | No, It was lifting leaves to see what's under. |
|
| |
|
Joined:
August 2002
Posts: 8307
Location: Tennessee | Which proved to be loc'dtite. |
|
| |
|
Joined:
March 2002
Posts: 14842
Location: NJ | Yeah, but a generous application of alcohol'll allow those leaves to lift MUCH easier (and often loosens up what's been loc'dtite!!). |
|
| |
|
Joined:
October 2002
Posts: 56
Location: Alabama | Ah Yes I remember those days... a little Boones Farm and some Sweet Baby James and those leaves would fall like October in CT. ;) |
|
| |
|
Joined:
June 2002
Posts: 164
Location: Denton, Texas | :( I just tried to change the strings on my 1987 Collectors and when I got all the strings off the nut fell off. Since you mention locktite, is that what is recommended to glue the nut back on? Or would it be wiser to take it to an Ovation repair facility or ship to Hartford? |
|
| |
|
Joined:
May 2002
Posts: 3005
Location: Las Cruces, NM | And you people accuse me of changing the subject. It might be a while, George, before they can get back to any sensible discussion of this subject. The words "pantyhose" and penetration" seem to have sparked a frenzy of sorts. These people seem to have a very short span of attention, shame shame. (a '52 Oldsmobile, her's not mine, seemed to have the needed effect without any excuses about belts in '55 in Virginia)
Bailey |
|
| |
|
Joined:
March 2002
Posts: 15664
Location: SoCal | George:
Take it to a good repair guy in your area. It'll be faster and cheaper than sending the guitar to Ovation. Any decent repair person can put the nut on properly.
Paul |
|
| |
Peeling Grape Leaves
