Wanted-Breadwinner PU selector toggle
Squarepeg
Posted 2008-12-31 8:17 PM (#296342)
Subject: Wanted-Breadwinner PU selector toggle


Joined:
December 2008
Posts: 3

Anyone know where I can get a replacement PU selector toggle for a Breadwinner?
Top of the page Bottom of the page
Mr. Ovation
Posted 2008-12-31 9:00 PM (#296343 - in reply to #296342)
Subject: Re: Wanted-Breadwinner PU selector toggle


Joined:
December 2001
Posts: 7222

Location: The Great Pacific Northwest		send me an email mileskb at aol.com
Top of the page Bottom of the page
MWoody
Posted 2008-12-31 9:11 PM (#296344 - in reply to #296342)
Subject: Re: Wanted-Breadwinner PU selector toggle



Joined:
December 2003
Posts: 13987

Location: Upper Left USA		Can you obtain a picture and possibly any ID number on the unit?

And Welcome!

Probably the 4PDT, On-On-On with the longer Wire lugs.

Top of the page Bottom of the page
Squarepeg
Posted 2009-01-03 7:59 AM (#296345 - in reply to #296342)
Subject: Re: Wanted-Breadwinner PU selector toggle


Joined:
December 2008
Posts: 3

I haven't taken it apart; it's still strung up. It should be Ovation part #487002-X-15 (Selector Switch JBT J0331). I'm guessing it's on-on-on.
Top of the page Bottom of the page
numbfingers
Posted 2009-01-03 10:41 AM (#296346 - in reply to #296342)
Subject: Re: Wanted-Breadwinner PU selector toggle


Joined:
January 2006
Posts: 1118

Location: NW Washington State
Originally posted by Squarepeg:
I haven't taken it apart; it's still strung up. It should be Ovation part #487002-X-15 (Selector Switch JBT J0331). I'm guessing it's on-on-on.
Don't count on it, unless Miles has told you that all these switches are the same. There were several versions of the preamp and they use some weird custom parts. Woody's suggestion to get positive ID is a good one.

-Steve W.
Top of the page Bottom of the page
alpep
Posted 2009-01-03 12:42 PM (#296347 - in reply to #296342)
Subject: Re: Wanted-Breadwinner PU selector toggle


Joined:
December 2001
Posts: 10582

Location: NJ		how many you need?
Top of the page Bottom of the page
Mr. Ovation
Posted 2009-01-03 2:35 PM (#296348 - in reply to #296342)
Subject: Re: Wanted-Breadwinner PU selector toggle


Joined:
December 2001
Posts: 7222

Location: The Great Pacific Northwest		To my knowledge, unless someone has rewired the pre-amp there are two switches. A 4P3T and a 3PDT, the larger being the pickup selector.

If it has been re-wired, then putting the correct switch in as a replacement should be easy enough unless someone butchered the board.
Top of the page Bottom of the page
MWoody
Posted 2009-01-03 5:33 PM (#296349 - in reply to #296342)
Subject: Re: Wanted-Breadwinner PU selector toggle



Joined:
December 2003
Posts: 13987

Location: Upper Left USA		RE: "Woody's suggestion to get positive ID is a good one."

For the record, I am between 5'8" and 6'2" depending on which Seven-Eleven I was last seen exiting.
Top of the page Bottom of the page
Squarepeg
Posted 2009-01-03 10:38 PM (#296350 - in reply to #296342)
Subject: Re: Wanted-Breadwinner PU selector toggle


Joined:
December 2008
Posts: 3

I believe it's all original; it's an early model, serial #E00093.
Top of the page Bottom of the page